Titulação Condutométrica

Monitoramento de uma titulação usando condutividade elétrica

Titrations Advanced (University) 50 min ~$20,00

Objetivo

Realizar uma titulação ácido-base usando medições de condutividade em vez de um indicador, e determinar o ponto final a partir de um gráfico condutividade-volume.

Contexto

In a conductometric titration, electrical conductivity of the solution is measured as the titrant is added. Since different ions have different molar conductivities (H+ and OH- are exceptionally mobile), the conductivity changes non-linearly during titration. The endpoint is found where two straight-line segments of the conductivity curve intersect.

Avisos de segurança

  • HCl and NaOH are corrosive
  • Wear safety goggles and gloves
  • Keep the conductivity probe away from the magnetic stirrer bar

EPI necessário

goggles gloves lab_coat

Materiais

  • Hydrochloric acid (HCl) (100 mL)
    0.1M
  • Sodium hydroxide (NaOH) (100 mL)
    0.1M
  • Distilled water (200 mL)

Equipamentos

50 mL burette Burette stand and clamp 250 mL beaker Conductivity meter with probe Magnetic stirrer 25 mL pipette Graph paper

Procedimento

1

Pipette 25.0 mL of 0.1M HCl into the beaker. Add 50 mL of distilled water to increase volume for the probe.

3 min Handle HCl carefully
2

Place the beaker on the magnetic stirrer. Insert the conductivity probe and the stir bar.

2 min
3

Record the initial conductivity reading. Fill the burette with 0.1M NaOH.

3 min
4

Add 1.0 mL of NaOH from the burette. Stir for 30 seconds, then record the conductivity and cumulative volume.

2 min
5

Repeat step 4, adding 1.0 mL increments, recording conductivity after each addition. Continue until well past the expected endpoint.

25 min
6

Plot conductivity (y-axis) versus volume of NaOH added (x-axis). Identify the two linear regions.

8 min
7

Draw best-fit lines for the two regions and find their intersection. This is the endpoint.

5 min

Resultados esperados

Conductivity initially decreases as highly mobile H+ ions are replaced by less mobile Na+ ions. After the endpoint, conductivity increases as excess OH- ions accumulate. The V-shaped graph clearly shows the equivalence point.

Limpeza

Remove and rinse the conductivity probe carefully. Neutralize waste solutions before disposal. Rinse all glassware.

Detalhes

Categoria
Titrations
Dificuldade
Advanced (University)
Duração
50 min
Custo estimado
$20,00
Passos
7
Materiais
3

Mais experimentos

Curva de Titulação de pH 50 min Retrotitulação de Comprimidos Antiácidos 60 min Titulação Ácido-Base com Alaranjado de Metila 40 min Titulação Ácido-Base com Fenolftaleína 45 min Titulação com Duplo Indicador de Mistura Carbonato-Bicarbonato 55 min Titulação Complexométrica com EDTA para Dureza da Água 45 min Titulação de Vitamina C com Iodo 40 min Titulação Iodométrica de Alvejante 50 min Titulação por Precipitação (Método de Mohr) 45 min Titulação Redox com Permanganato de Potássio 50 min

Frequently Asked Questions

What is the objective of Titulação Condutométrica?
Realizar uma titulação ácido-base usando medições de condutividade em vez de um indicador, e determinar o ponto final a partir de um gráfico condutividade-volume.
How difficult is Titulação Condutométrica?
This experiment is rated as Advanced (University). It takes approximately 50 minutes to complete.
What safety precautions are needed for Titulação Condutométrica?
Key safety precautions include: HCl and NaOH are corrosive; Wear safety goggles and gloves; Keep the conductivity probe away from the magnetic stirrer bar.
What materials are needed for Titulação Condutométrica?
The main materials required are: Hydrochloric acid (HCl), Sodium hydroxide (NaOH), Distilled water.
What results should I expect from Titulação Condutométrica?
Conductivity initially decreases as highly mobile H+ ions are replaced by less mobile Na+ ions. After the endpoint, conductivity increases as excess OH- ions accumulate. The V-shaped graph clearly shows the equivalence point.